STI Engineering rfi-9256 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 109

background image

RFI-9256 Radio Modem

User Manual

DISCLAIMER

© 2017 STI Engineering Pty Ltd. All rights reserved.

STI Engineering reserves the right to make improvements on the product in this manual at any time
without notice.

No part of this manual may be produced, copied, translated, or transmitted in any form or by any means
without the written permission of STI Engineering.

Information provided in this manual is intended to be accurate and reliable. However, STI Engineering
assumes no responsibility for its use or infringements upon the rights of third parties that may result from
its use.

FCC NOTIFICATIONS

This device must be operated as supplied by STI Engineering. Any changes or modifications made to the
device without the express written approval of STI Engineering may void the user's authority to operate
the device.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference and 2) this device must accept any interference received,
including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to  Part 15 of the  FCC Rules. These limits  are designed to  provide reasonable protection against harmful
interference  in  a  residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio  frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio  communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular
installation.  If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.



Consult the dealer or an experienced radio/TV technician for help.

Reference No. MAN00005

Revision 5.5

February 2017

Firmware Version: 1.24I (1.24O)

www.esis.com.au

Ph 02 9481 7420

Fax 02 9481 7267

[email protected]

«
1
2
3
4
...
»

Содержание rfi-9256














































































































Отзывы:

Нет отзывов

Похожие инструкции для rfi-9256

Badradio SR-300

Бренд: Hama Страницы: 3

Бренд: US Robotics Страницы: 129

Бренд: Salora Страницы: 21

Бренд: Radio Shack Страницы: 20

Бренд: Flexitron Страницы: 100

Бренд: Alcatel Страницы: 33

Бренд: COP-USA Страницы: 11

Бренд: Garmin Страницы: 28

VHF 300 - Marine Radio

Бренд: Garmin Страницы: 6

PlusTV Hybrid Stick

Бренд: KWorld Страницы: 10

Бренд: Realme Страницы: 24

Бренд: Kogan Страницы: 36

Бренд: Go Страницы: 2

Бренд: Entel Страницы: 24

Бренд: Xact Страницы: 67

Бренд: DNT Страницы: 104

Бренд: Clas Ohlson Страницы: 44

Бренд: F.u.n.k.e. Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды