STI Engineering rfi-9256 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 109

background image

Appendix C Hayes AT Command Reference

RFI-9256 Radio Modem User Manual

Page 87 of 109

Command

Description

ATI

Displays the firmware identifier.

ATI0

Displays the numeric identify code (UNIRADIO PnP).

ATI1

Displays the CRC-32 firmware checksum.

ATI2

Returns OK if the firmware checksum is correct, or ERROR if the firmware checksum is
invalid.

ATI3

Displays the firmware revision level.

ATI4

Displays the firmware revision / build date.

ATI5

Displays the radio manufacture date.

ATI6

Displays the radio serial number.

ATI7

Displays the mode identification string.

ATI8

Displays the connection type.

ATI9

Displays the internal temperature of the radio in degrees C.

ATI10

Displays the offline time in milliseconds.

ATI11

Displays the radios average RSSI in dBm.

ATI12

Displays the radios average NOISE in dBm.

ATI13

Displays the current port identifier (0 for main, 1 for aux, or 2 for a virtual Hayes dial-up
port).

ATI14

Displays the radio link status.

Table 22: ATI information commands

C.1.6

“ATO” Return to Online State

The return to online state command returns the radio to online state from local command state.

When a radio is online (connected to a remote computer), anything transmitted over the serial port is sent to
the remote unit. In order to send AT commands to the radio, it must be returned to local command state. This
is done by sending an escape sequence (see section Escape Sequence on page 35). In order to go back online
state from the local command state, the

ATO

command is executed.

C.1.7

“ATQ” Quiet (Suppress Response Codes)

The response codes that are generated by the radio can be suppressed, so that commands do not return

OK

,

CONNECT

, or

NO CARRIER

. The options for generating response codes are shown in Table 23.

«
...
85
86
87
88
89
...
»

Содержание rfi-9256














































































































Отзывы:

Нет отзывов

Похожие инструкции для rfi-9256

Бренд: ABB Страницы: 6

Бренд: Patton electronics Страницы: 10

Бренд: Pacific Crest Страницы: 2

Бренд: Paradyne Страницы: 22

COMSPHERE 3000 Series

Бренд: Paradyne Страницы: 131

Бренд: GPX Страницы: 2

Бренд: Teac Страницы: 2

Бренд: NextNet Страницы: 26

Бренд: GME Страницы: 33

Бренд: Uniden Страницы: 104

FSMODEM-CELLBASE

Бренд: Federal Signal Corporation Страницы: 16

Бренд: Eaton Страницы: 83

Бренд: ZyXEL Communications Страницы: 70

Бренд: Cobra Marine Страницы: 22

Бренд: RACOM Страницы: 189

Бренд: JRC Страницы: 4

Бренд: COP-USA Страницы: 11

Бренд: Cisco Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды