Stentofon alphaCom XE Скачать руководство пользователя страница 17

Страница: 17 / 68

AlphaCom XE - Installation, Configuration & Operation

A100K10805

Performing a Cold Start

2.3

A cold start of the AMC-IP board will delete all previous programming,

load the default database and set the default IP address to 169.254.1.5

with mask 255.255.0.0 on Eth0. See section 3.4 for default settings.

2.3.1 Cold start procedure

Turn the server mains switch ON (at the rear of the cabinet).

●

Press and hold the cold start button on the AMC-IP board.

●

Press the reset button on the APC card briefly.

●

XE7: the reset button is located on the power card

XE1: Power up while keeping the cold start button pressed.

Keep the cold start button pressed at least 1 second after reset.

●

The AMC status LED will blink green when the boot is ready.

2.3.2 Cold start AMC application only (retain IP setting)

Press the reset button on the APC card briefly.

●

XE7: the reset button is located on the power card

XE1: Power up while keeping the cold start button pressed.

After 10 seconds, press the cold start button on the AMC-IP board.

●

Keep the cold start button pressed until the AMC running LED blinks

●

green.

Modifying Factory Default Settings

2.4

The system is set up with a default program and works without any

further programming. To change or add to the default settings, the

AlphaPro programming tool must be used - see section 5.
Perform System Backup if any default setting has been changed - see

section 12. The default parameters are restored by performing a cold

start - see section 2.3.

Default Directory and Feature Numbers

2.5

2.5.1 Station numbers

The number series 101 to 499 and 5000 to 5152 are default directory

numbers for all AlphaCom XE servers. The directory numbers are

connected to physical numbers in the range from 1 to 552, where the

physical numbers are given by the subscriber point on a board in a

certain position in a defined module.
Since the card positions 2-7 are not used in XE20, the corresponding

default subscriber numbers are missing.
The directory numbers can be changed by using the AlphaPro

programming tool.

ANALOG STATION NUMBER TABLE

AlphaCom modules

XE7

XE20

XE26

Single or master

101 - 136

101 - 106

143 - 238

101 - 238

slave*

239 - 274

239 - 244

281 - 376

239 - 376

slave*

377 - 413

377 - 382

419 - 499

5000 - 5014

377 - 499

5000 - 5014

slave*

5015 - 5051

5015 - 5020

5057 - 5152

5015 - 5152

Display text

Station 1, Station 2, etc.

>1 sec

RESET - APC

COLD START - AMC

Status LED

10 sec

RESET - APC

COLD START - AMC

Status LED

XE 26

138

XE 7

XE 20

102

ASLT board

108

109

110

111

112

107

Physical number

1...6

7...12 13...18 19...24 25...30 31...36

Single /first module

Subscriber number

* Slave modules are only required for

analog stations. IP stations are always

registered to the master module.

Содержание alphaCom XE





































































Результаты поиска

Содержание alphaCom XE

Отзывы:

Похожие инструкции для alphaCom XE

Бренды по названию

Популярные бренды

Stentofon alphaCom XE, Установка, настройка и эксплуатация

Результаты поиска

Содержание alphaCom XE

Отзывы:

Похожие инструкции для alphaCom XE

Бренды по названию

Популярные бренды