background image

 

 

27

EEProm 
Error 

The EEProm of the controller cannot be read or 
described any longer. Remedy: interrupt the 
controller’s supply of voltage and reconnect it 
again. If the error cannot be cleared, please see 
your authorised dealer 

  Disconnect the charge 

controller and reconnect it in 
the order described. If the 
indication remains, the 
controller must return to the 
dealer for repair. 

self test 
failure 
 

The self-test could not have been carried out 
correctly, since the solar generator or the load 
had not been disconnected. On of the power 
components or any other does not function 

  Disconnect module and load 

  If the self-test still failed, the 

controller should be sent to 
the producer. 

Night 

“night” message during the day  
no “night” message during night 

  Module polarity wrong 

  Parallel blocking diodes with 

20 kOhm 

14 

13B

Legal Guarantee 

In accordance with German statutory regulations, there is a 2-year legal guarantee on this product for the 
customer.  

The seller will remove all manufacturing and material faults that occur in the product during the legal 
guarantee period and affect the correct functioning of the product. Natural wear and tear does not 
constitute a malfunction. Legal guarantee does not apply if the fault can be attributed to third parties, 
unprofessional installation or commissioning, incorrect or negligent handling, improper transport, 
excessive loading, use of improper equipment, faulty construction work, unsuitable construction location 
or improper operation or use. Legal guarantee claims shall only be accepted if notification of the fault is 
provided immediately after it is discovered. Legal guarantee claims are to be directed to the seller.  

The seller must be informed before legal guarantee claims are processed. For processing a legal 
guarantee claim an exact fault description and the invoice / delivery note must be provided.  

The seller can choose to fulfil the legal guarantee either by repair or replacement. If the product can 
neither be repaired nor replaced, or if this does not occur within a suitable period in spite of the 
specification of an extension period in writing by the customer, the reduction in value caused by the fault 
shall be replaced, or, if this is not sufficient taking the interests of the end customer into consideration, the 
contract is cancelled. 

Any further claims against the seller based on this legal guarantee obligation, in particular claims for 
damages due to lost profit, loss-of-use or indirect damages are excluded, unless liability is obligatory by 
German law. 

  

15 

14B

Accessories 

Current sensor 200A   

PA HS200 

 

Power line receiver   

PA 15   

Load relais 200A 

 

PA EV200 

Battery temp.sensor   

PA TS10 (included)   

Data logger   

 

TarCom (opt. GSM modem, ethernet) 

Содержание Power Tarom 2070





























Отзывы: