stayer EPG300, Руководство по эксплуатации

Страница: 19 / 36

Never clean the nozzle and air holes of the spray gun with
pointed metal objects. Do not pour diluted spray material
back into the original spray material drum/tin for storage.
Clean the spray gun thoroughly after having sprayed
material hazardous to one's health.
– Unplug the mains plug and pull the trigger switch 16 so
that the spraying material can flow back into the container.
– Remove the electrical unit.
– Unscrew the container
11 and empty the remaining spray
material.
– Fill diluting agent (paint thinner or water) into the container
and screw it to the spray gun.
– Shake the spray gun several times.
– Connect the spray gun to the electrical unit again.
– Plug the mains plug into a socket outlet, pull the trigger
switch and spray the diluting agent into an empty material
tin.
– Repeat the process until clear diluting agent emerges
from the spray gun.
Unplug the mains plug and remove the electrical unit.
– Completely empty the container 11 .
– Check if the suction tube with the container seal 10 is free
of spray material and undamaged.
– Clean the outside of the container and the spray gun with
a cloth moistened in paint thinner.
– Unscrew the union nut
14 and the air cap 13 .
– Clean the nozzle 20 and the nozzle needle with diluting
agent.
From time to time, the nozzle seal 21 must also be
cleaned.
– Mount the air cap 13 onto the nozzle and tighten with the
union nut 14 .
Changing the Air Filter (Fig.10)
Never operate the powr tool without the air filter.
Without the air filter, dirt/contamination
can be drawn in and can influence the operation
of the power tool.
The air filter must be replaced when soiled.
– Remove the air filter cover
3 , taking into account the 7
hooks that hold the filter cover 3 .
– Replace the air filter 8 .
– Reattach the air filter cover and screw in the screw again.
5.2 Repair service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as well
as spare parts. Exploded views and information on spare
parts can also be found under:
info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
4.2 Adjustment operation (Fig.7)
Preparing for Operation
Spraying on the sides of water bodies (lakes, rivers,
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
When purchasing paint, varnish and spray material, pay
attention to their environmental compatibility.
Preparing the Spray Surface
Cover off the vicinity of the spray surface
thoroughly and generously.
The spray mist contaminates the environment. When
spraying in enclosures, surfaces not covered can become
contaminated. The spray surface must be clean, dry and
grease-free.
– Roughen smooth surfaces and then remove the sanding
dust.
Preparation of material (fig.11)
1. Mix the material well before measuring viscosity.
2. Completely submerge the cup viscometers, in the
material to be sprayed.
3. Hold the cup test and measure time in seconds until all
the liquid is emptied and this corresponds to time (seconds)
depending on the material supplied as appropriate, in the
following table.
Table Preparation of material:
4.3 Correction of Malfunctions
See table page 17 and 18
5. Maintenance and service instructions
Before any work on the machine itself, pull the
mains plug.
5.1 Cleaning (Fig.9)
Never immerse the electrical unit into solvent or water.
Clean the housing using only a moist cloth.
Proper cleaning is the requirement for flawless operation of
the spray gun. Improper or lack of cleaning voids warranty
claims.
Always clean the spray gun and the container with the
respective diluting agent (paint thinner or water) for the
spray material being used.
Material
Oil Painting
Oil Primer
Coating
Time (sec)
25-40
30-45
20-50
ENGLISH
15
15