Stanley SGV115, Оригинальное руководство пользователя

Страница: 9 / 28

(Original instructions)
ENGLISH
9
If the RCD causes power disconnection, have the tool sent to
an authorized Stanley dealer for repair.
WARNING! Under extreme working conditions, conductive
dust and grit may accumulate on the housing interior when
handling metal workpieces.
This could create an electric shock hazard as it weakens the
protective insulation in the grinder.
To avoid accumulation of metal chips in the interior of the
grinder, we recommend cleaning the ventilation ducts
daily.Refer to Maintenance.
Using Grinding Wheels
WARNING! Metal powder accumulates. Excessive use of the
grinding wheel on metals may increase the risk of electric
shock. To reduce the risk, insert the RCD before use and
clean the ventilation ducts daily. Follow the maintenance
instructions below to blow dry compressed air into the
ventilation ducts.
GRINDING
Surface Grinding with Grinding Wheels
1. Allow the tool to reach full speed before touching the tool
to the work surface.
2. Apply minimum pressure to the work surface, allowing the
tool to operate at high speed. Grinding rate is greatest
when the tool operates at high speed.
3. Maintain a 20˚ to 30˚ angle between the tool and work
surface.
4. Continuously move the tool in a forward and back motion
to avoid creating gouges in the work surface.
5. Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
Precautions to Take when Sanding Paint
• Sanding of lead based paint is NOT RECOMMENDED
due to the difficulty of controlling the contaminated dust.
The greatest danger of lead poisoning is to children and
pregnant women.
• Since it is difficult to identify whether or not a paint
contains lead without a chemical analysis, we recommend
the following precautions when sanding any paint.
GENERAL INFORMATION
Helpful Hints
• Hold your angle grinder with one hand on the body and
the other hand firmly around the side handle as shown in
Fig. J.
• Always position the guard so that as much of the exposed
disc as possible is pointing away from you. ff Be prepared
for a stream of sparks when the disc touches the metal.
• Maintain an angle between the disc and work surface (Fig.
J) of approximately 30° when grinding and 10°- 15° when
sanding (Fig. K) for best tool control, material removal, and
minimal loading.
CAUTION!
Use extra care when grinding into a corner as a
sudden, sharp movement of the grinder may be experienced
when the wheel contacts a secondary surface.
WARNING! Always wear eye protection while operating this
power tool.
Pop-off Brushes
The motor will be automatically shut off indicating that the
carbon brushes are nearly worn out and that the tool needs
servicing. The carbon brushes are not user-serviceable. Take
the tool to an authorised STANLEY repair agent.
Maintenance
Your Stanley corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. To ensure satisfactory operations, the tool
must be maintained and cleaned regularly
WARNING! To minimize the danger of serious personal
injury, please switch off the tool power and disconnect all
plugs before adjusting or removing/ installing any
accessory. Before reassembling the tool, press and release
the trigger switch to make sure the tool is already switched off.
WARNING! Before performing any maintenance on corded/
cordless power tools:
Lubrication
Stanley tools are properly lubricated at the factory
and are ready for use.
Tools should be lubricated regularly every year depending on
usage. (Tools used on heavy duty jobs and tools exposed to
heat may require more frequent lubrication.) This lubrication
should be attempted only by trained power tool repairperson’s
such as those at Stanley service centers or in other qualified
service personnel.
Cleaning
WARNING! Dust and grit from metal grinding often
accumulate on interior surfaces and could create an
electrical shock hazard if not cleaned out. Use only
mild soap and a damp cloth to clean the tool. Never
let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING! Never use solvents or harsh chemicals
to clean non-metal parts of the tool. These
chemicals may weaken the material of the parts.
Use only mild soap and damp cloth to clean the
tool. Never let any liquid get inside the tool; never
immerse any part of the tool into liquid.
WARNING! Do not overload your angle grinder.
Overloading causes a reduction in speed and
efficiency, causing your angle grinder to become too
hot. If this happens, operate your angle grinder
under no load for one or two minutes until it has
cooled to normal operating temperature. Switching
your angle grinder off under load will reduce the life
of the switch.