Standard Change-Makers CMP-20 Скачать руководство пользователя | Manualshive

Страница: 29 / 56

background image

Page 29 of 56

SETTINGS are used in calculating sold out. The Alert Level setting is not used and it is only used to
send an email alert. The Fill Level and Alert Level are entered with the EF+ but stored in the
dispenser.

The bill dispenser will be calculated to be sold out when the Fill Level - Dispense Count is less than
or equal to the Bin Low count value. The Bin Low count value is defaulted to 30 notes for the Mini-
Mech. If you need to change the Bin Low count value, please see the Modular Machine Series
manual (8M00420) on how to do this. The Bin Low count value is used to guarantee one last
dispense.

If the Fill Level is not greater than the Bin Low count value, the dispenser will show a flash code of
12 and the EF+ will show a PROGRAM error at that location. This is a fatal error for the machine.

Examples

Fill Level

Dispense Count

Sold Out

1000 950

No

1000 969

No

1000 970

Yes

25 0

error

500 100

No

This assumes a Bin Low count value of 30

«
...
27
28
29
30
31
...
»

Содержание CMP-20

























































Отзывы:

Нет отзывов

Похожие инструкции для CMP-20

Бренд: CashConcepts Страницы: 2

Бренд: Electro Industries/GaugeTech Страницы: 216

Бренд: Standard Change-Makers Страницы: 12

LoRaWAN TCR-LSA

Бренд: Parametric Страницы: 8

Бренд: Hengstler Страницы: 6

Бренд: Hengstler Страницы: 5

Бренд: Tense Страницы: 6

Бренд: EnOcean Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды