SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 53

background image

14

Lower Leg Seal Service

Hold the lower leg firmly and use the seal installation tool to push

the lower oil seal evenly into the leg until the bottom surface of

the seal is flush with the bottom of the seal pocket.

Remove the wire spring from the new dust wiper seal and set the

spring aside.
Insert the narrow end of the new dust wiper seal into the recessed

end of the 35 mm seal installation tool.

Hold the lower leg firmly and use the seal installation tool to push

the dust wiper seal evenly into the lower leg until the seal surface

is flush with the top of the lower leg surface.
Reinstall the wire spring onto the dust wiper seal.
Repeat on the other side.

5

35 mm seal installation tool

35 mm seal installation tool

6

7

35 mm seal installation tool

«
...
12
13
14
15
16
...
»

Содержание 2015 BOXXER TEAM






















































Отзывы:

Нет отзывов

Похожие инструкции для 2015 BOXXER TEAM

Бренд: Panasonic Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: B-TEK Scales Страницы: 3

Бренд: B-Speech Страницы: 18

Бренд: B-PWR Страницы: 12

Бренд: Caberg Страницы: 3

Бренд: Caberg Страницы: 2

Бренд: Dacor Страницы: 4

Бренд: Feniex Страницы: 6

Бренд: Fencing SmartBox Страницы: 11

Бренд: Feiyu Страницы: 4

Бренд: FAZUA Страницы: 84

Бренд: GAI-Tronics Страницы: 22

Бренд: ICON Страницы: 8

Бренд: National Instruments Страницы: 11

Бренд: VDO Cyclecomputing Страницы: 21

Бренд: Panasonic Страницы: 120

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды