SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 45

Страница: 45 / 53

Charger Damper™ Assembly and Bleed

Spray isopropyl alcohol on the Charger Damper™ assembly and

clean it with a rag.

Insert the Charger Damper assembly into the top of the upper

tube that has the BoXXer™ graphic printed on it.
Use a torque wrench with a 24 mm socket to tighten the

compression top cap to 7.3 N•m (65 in-lb).

Apply SRAM® Butter to the scraper in the lower seal head and

install it onto the rebound shaft with the flat side of the lower seal

head facing the upper tube. Push the lower seal head into the

bottom of the upper tube.
Push the rebound damper shaft into the upper tube to prevent it

from getting scratched while installing the retaining ring.

N OT I C E

Scratches on the rebound shaft will allow oil to bypass the seal

head into the lower leg, resulting in reduced performance.

Place the tips of large internal snap ring pliers into the eyelets of

the retaining ring and install the retaining ring into the groove.

Check that the retaining ring is properly seated in the retaining

ring groove by using the snap ring pliers to rotate the retaining

ring and seal head back and forth a few times, then firmly pull

down on the rebound shaft.

Retaining rings have a sharper-edged side and a rounder-edged

side. Installing retaining rings with the sharper-edged side facing

the tool will allow for easier installation and removal.

Use your fingers to install the bottom out bumper onto the

rebound damper shaft with the smaller end pointed away from the

top.

24 mm

7.3 N•m (65 in-lb)

Содержание 2015 BOXXER TEAM






















































Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды

SRAM 2015 BOXXER TEAM, Руководство по обслуживанию

Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды