SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 48

Страница: 48 / 53

Lower Leg Assembly

Slide the lower leg assembly along the upper tubes until it stops

and the spring and damper shafts are visible through the lower leg

bolt holes.
Use a rag to clean the outer surface of the lower leg.

Install a new crush washer retainer and crush washer on the

non-drive side and drive side bottom bolts.

N OT I C E

Dirty or damaged crush washers can cause leaks.

Thread the black bottom bolt into the non-drive side shaft of the

lower leg. Thread the silver bottom bolt into the drive side shaft of

the lower leg.
Use a torque wrench with a 5 mm hex bit socket to tighten the

bolts to 7.3 N·m (65 in-lb).

Install the rebound adjuster knob onto the drive side bottom bolt.
Use a torque wrench with a 2.5 mm hex bit socket to tighten the

set screw to 1.1 N·m (10 in-lb).

N OT I C E

Make sure to hold the rebound adjuster knob in place during

installation of the set screw to prevent damage to the bottom bolt.

Spray isopropyl alcohol on the entire fork and clean it with a rag.

Non-drive side

Drive side

5 mm

7.3 N

m (65 in-lb)

5 mm

7.3 N

m (65 in-lb)

2.5 mm

1.1 N

m (10 in-lb)

Содержание 2015 BOXXER TEAM






















































Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды

SRAM 2015 BOXXER TEAM, Руководство по обслуживанию

Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды