SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 8

Страница: 8 / 53

Fork Removal

F o r k R e m o v a l

We recommend the following steps to remove your BoXXer™ fork from the bicycle. Removing the fork from the bicycle provides easy

access to internal components and is more convenient than working around a complete bicycle.

To assist you with post-service assembly, record the distance from

the top of the upper tube to the top of the lower crown.

Use a 6 mm hex wrench to loosen the non-drive side bolt of the

Maxle Lite DH™ until detent clicks are no longer felt.

Use a 6 mm hex wrench to remove the Maxle Lite DH from the

drive side of the fork. Pull the wheel down to remove it from the

fork.

27.5" forks:

Use a 2.5 mm hex wrench to remove the brake hose

from the hose brace on the fork arch.

26" forks:

Use a diagonal cutter to cut the cable tie holding the

brake hose to the fork arch.
Remove the brake caliper according to the brake manufacturer's

instructions.

space between frames

space between steps

6 mm

Содержание 2015 BOXXER TEAM






















































Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды

SRAM 2015 BOXXER TEAM, Руководство по обслуживанию

Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды