SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 53

background image

13

Lower Leg Seal Service

L o w e r L e g S e a l S e r v i c e

Place a rag on top of the dust wiper seal. Insert the tip of a

downhill tire lever underneath the lower lip of the lower black oil

seal located above the upper bushing.

N OT I C E

If using a flat head screwdriver, make sure it has a round shaft. A

screwdriver with a square shaft will damage the lower leg.

Stabilize the lower leg on a bench top or on the floor. Press down

on the downhill tire lever handle to remove both seals at the same

time. Repeat on the other side.

N OT I C E

Keep the lower leg assembly stable. Do not allow the lower leg to

twist in opposite directions, compress toward each other, or be

pulled apart. This will damage the lower leg.

Spray isopropyl alcohol on the inside and outside of the lower leg

and clean it with a rag.
Wrap a rag around a long dowel and insert it into each lower leg to

clean the inside.

Position the new lower oil seal, with the grooved side visible, onto

the stepped side of a 35 mm seal installation tool.

1

Downhill tire lever

2

3

35 mm seal installation tool

4

«
...
11
12
13
14
15
...
»

Содержание 2015 BOXXER TEAM






















































Отзывы:

Нет отзывов

Похожие инструкции для 2015 BOXXER TEAM

Бренд: Eaton Страницы: 21

Бренд: AC Schnitzer Страницы: 16

Бренд: Watts Страницы: 8

Бренд: HALE Страницы: 44

Бренд: Karella Страницы: 20

Бренд: Jetter Страницы: 4

Бренд: K&K Страницы: 8

Бренд: K&K Страницы: 20

Бренд: K&K Страницы: 6

Бренд: K&K Страницы: 3

Бренд: K&K Страницы: 3

Бренд: Magura Страницы: 2

Бренд: Zacuto Страницы: 5

Бренд: Öhlins Страницы: 2

Mechatronics 35007-01

Бренд: Öhlins Страницы: 4

McPherson Strut MIR 5H02

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 4

Бренд: Mahindra Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды