SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 47

Страница: 47 / 53

Lower Leg Assembly

L o w e r L e g A s s e m b l y

Spray isopropyl alcohol on the upper tubes and clean them with a

rag.

Apply a liberal amount of SRAM® Butter to the inner surfaces of

the lower oil seals and dust wiper seals.

Slide the upper tube with the Charger Damper™ into the drive side

lower leg just enough to engage the upper bushing with the upper

tube.
Slide the upper tube with the coil spring into the non-drive side

lower leg just enough to engage the upper bushing with the upper

tube.

N OT I C E

Make sure both dust wiper seals slide onto the tubes without

folding the outer lip of either seal.

Clamp the upper tube into a bicycle stand. Position the fork at a

slight angle with the lower leg bolt holes oriented upward. Angle

a syringe fitting in each lower leg bolt hole so the fluid will only

contact the inside of the lower leg.
Inject 10 mL of RockShox

0w-30 suspension fluid into the drive

side lower leg, and 20 mL of RockShox 0w-30 suspension fluid

into the non-drive side lower leg.

N OT I C E

Do not exceed the recommended fluid volume per leg as this can

damage the fork. Do not let fluid fill the rebound shaft.

DS: 10 mL NDS: 20 mL

RockShox 0w-30 suspension fluid

Содержание 2015 BOXXER TEAM






















































Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды

SRAM 2015 BOXXER TEAM, Руководство по обслуживанию

Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды