SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 50

Страница: 50 / 53

Fork Installation

Use a torque wrench with a 4 mm hex bit socket to tighten the top

bolt on the lower crown to 5 N

•

m (44 in-lb). Use a 4 mm hex bit

socket to tighten the bottom bolt on the lower crown to

5 N

•

m (44-lb). Tighten the top bolt to torque once more, and then

tighten the bottom to torque again.
Repeat this tightening procedure for the bolts on the other side of

the lower crown.

Use a torque wrench with a 4 mm hex bit socket to tighten the

two upper crown pinch bolts to 5 N

•

m (44 in-lb).

27.5" fork:

Use a 2.5 mm hex wrench to install the brake hose in

the hose brace on the fork arch.

26.5" fork:

Use a cable tie to connect the brake hose to the fork

arch.
Install the brake caliper according to the brake manufacturer's

instructions.

Position the front wheel in the lower leg dropouts so the hub is

seated in the dropouts.

N OT I C E

Verify no parts interfere with the lower leg. Consult your brake

manufacturer's instructions if you need to adjust your disc brakes.

4 mm

5 N•m (44 in-lb)

4 mm

5 N•m (44 in-lb)

Содержание 2015 BOXXER TEAM






















































Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды

SRAM 2015 BOXXER TEAM, Руководство по обслуживанию

Результаты поиска

Содержание 2015 BOXXER TEAM

Отзывы:

Похожие инструкции для 2015 BOXXER TEAM

Бренды по названию

Популярные бренды