SRAM 2015 BOXXER TEAM Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 53

background image

11

Lower Leg Removal

Clamp the drive side upper tube into a bicycle stand.

Use a 2.5 mm hex wrench to loosen the set screw and remove the

rebound adjuster knob located at the bottom of the drive side

lower leg.

Use a 5 mm hex wrench to loosen the drive side bottom bolt 3 to

4 turns.

Place an oil pan beneath the fork to catch any draining fluid.

Use a plastic mallet to firmly strike the drive side bottom bolt to

dislodge the rebound damper shaft from the lower leg.
Use a 5 mm hex wrench to remove the bottom bolt from the lower

leg.

Do not dislodge the silver casting plug from the drive side lower

leg.

Drive side

5

6

2.5 mm

7

5 mm

Loosen 3 to 4 turns

8

Plastic mallet

5 mm

«
...
9
10
11
12
13
...
»

Содержание 2015 BOXXER TEAM






















































Отзывы:

Нет отзывов

Похожие инструкции для 2015 BOXXER TEAM

BTL7-S5 B-M Series

Бренд: Balluff Страницы: 14

BML-S1G0 7 M5E 0 Series

Бренд: Balluff Страницы: 194

Бренд: Danfoss Страницы: 14

Odyssey II Series

Бренд: Dakota Digital Страницы: 3

Бренд: Land Pride Страницы: 4

Бренд: Land Pride Страницы: 3

Бренд: Manfrotto Страницы: 2

Бренд: Rally Pack Страницы: 2

Бренд: rako Страницы: 3

Бренд: Wattson Страницы: 19

Бренд: Warrior Winches Страницы: 17

Бренд: Zhiyun Страницы: 10

Бренд: Zigo Страницы: 150

Бренд: Coby Страницы: 16

Бренд: Memphis Shades Страницы: 2

Бренд: Peg-Perego Страницы: 16

Бренд: PullRite Страницы: 10

Бренд: Viking Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды