Spirax Sarco CSM-C Скачать руководство пользователя

Страница: 13 / 56

3.696.5275.210

Energy and Power Sources for Generating Steam

Spirax Sarco Compact Clean Steam Generators can be configured and manufactured to

use one (1) of two (2) possible energy sources for generating clean steam: (HTM 2031).

Steam:

Electricity

∆

Note: Most Spirax Sarco Compact Clean Steam Generators use steam as the

energy source for generating clean steam. Therefore, procedures detailed in this

manual will be geared towards the installation, operation, and maintenance of steam

powered units.

When procedures differ substantially for the installation, operation, and /or maintenance of

units powered with electricity, notes will be included giving specific instructions for those

units.

The following table lists the range of acceptable pressures and temperature at the inlet

for each energy source.

Energy source

Maximum Temperature °C /

Degree Centigrade

Maximum pressure

bar g

Steam

184°C

10 bar g

Electricity

Upon request

N/A

∆

Note: Consult the design specifications for the unit, as well as the nameplate

attached to the exterior of the pressure vessel and individual specification tags on

pressure related components and controls, for design specifications and maximum

pressure for the unit.

Controls

Spirax Sarco Steam Generators are equipped with both electronically and pneumatically

activated controls to regulate pressure (temperature) and water level. The electronic

PLC control panel used, depending on individual design specifications, has a power

requirement of 380 volt three phase. Pneumatic controls, depending on individual design

specifications, require instrument air pressures of 8 bar g (120 psi). Consult the individual

design specifications for the unit and controls for the exact requirements.

Construction

All Spirax Sarco Compact Clean Steam Generators are constructed from superior materials

and utilize only the highest quality components. All parts in contact with generated steam

are S.S. 316L. Each Compact Steam Generator meets or exceeds all applicable V.S.R

code (Vessel Security Rules) regulations and are built to conform to 97/23/CE Directive.

Each Spirax Sarco Compact Clean Steam Generator is equipped with a

approved

safety valve and an external drain, providing a means to remove accumulated sediment.

Содержание CSM-C

























































Результаты поиска

Содержание CSM-C

Отзывы:

Похожие инструкции для CSM-C

Бренды по названию

Популярные бренды

Spirax Sarco CSM-C, Инструкция по установке и обслуживанию

Результаты поиска

Содержание CSM-C

Отзывы:

Похожие инструкции для CSM-C

Бренды по названию

Популярные бренды