Solas TWENTY6 ST-26N Скачать руководство пользователя страница 53

Страница: 53 / 60

solasfires.com

GAS CONVERSION

GAS CONVERSION LABEL INSTRUCTIONS

1. When converting this fireplace, use a permanent marker to complete the supplied gas conversion label then affix it to

the right side of fireplace above the control module as pictured below.

2. Affix the supplied rating plate conversion label to the rating plate. Be sure to not cover the Model and Gas Pressure

information for the model and fuel you are converting to. With a permanent marker, check off the fuel type you are

converting to.

This Fireplace

has been

converted.

See conversion

label in fireplace.

This Fireplace

has been

converted.

See conversion

label in fireplace.

SÓLAS

This fireplace has been converted in the field. This label must

be filled out with indelible ink and affixed in a conspicuous

location near the appliance listing label.

Appliance Model: ______________ Converted to:

■

Gas Conversion Kit No. ____________________________________
This Appliance was Converted on (MM/DD/YYYY):  ______________
This Gas Conversion was Completed by:  ______________________
Address:  _______________________________________________

______________________________________________________

CAUTION:

This gas conversion must be completed by a licensed gas installer.

Manufactured by:

Progressive Manufacturing Inc., 452 Sunapee St., Newport, NH 03773 USA

Содержание TWENTY6 ST-26N





























































Результаты поиска

Содержание TWENTY6 ST-26N

Отзывы:

Бренды по названию

Популярные бренды

Solas TWENTY6 ST-26N, Руководство по установке и эксплуатации

Результаты поиска

Содержание TWENTY6 ST-26N

Отзывы:

Бренды по названию

Популярные бренды