Solas TWENTY6 ST-26N Скачать руководство пользователя страница 30

Страница: 30 / 60

SÓLAS

CONTEMPORARY FIRE

ASSEMBLY & INSTALLATION

Installing the Outer Vent Heat Shields and Vent

Termination (Parallel Installation on Outside Wall)
1. Before you install the horizontal vent termination,

you must first install the second halves of the two

telescoping vent pipe heat shields. Each shield half

simply slips over the half you previously attached to the

fireplace mounting plate and can now be seen inside

the vent pass-through in the wall.

2. Install the outer shield first and the inner second. Leave

about 1-1/4” of the shields protruding past the house

sheathing.

3. Install the horizontal vent termination (vent cap). Be

sure the arrow on the cap (if present) is pointing up and

reconfirm that all the vent cap location requirements

per page 18 and the vent manufacturers requirements

are met.

4. Slip the inner and outer vent termination pipes onto

the vent starter pipe taking care to align the inner and

outer pipes to prevent damage.

5. Slide the vent termination (cap) into the siding recess

(or vinyl siding shield) until it bottoms out.

Note: The

rear surface of the vent termination will push the

telescoping vent pipe heat shields inward. When the

vent termination is in place the heat shields will just

touch the rear surface of the termination.

6. Pull the vent cap away from the sheathing and install a

small bead of non-hardening silicone sealer around the

cap perimeter. Push the cap in place.

7. Install the mounting screws (included with the cap) to

hold the vent cap to the sheathing See the venting

manufacturers instructions for the location of the

mounting holes. Typical mounting hole locations

are shown in the adjacent photo. See the venting

manufacturers instructions for more information or if

using the vinyl siding shield.

Mounting

Holes

Содержание TWENTY6 ST-26N





























































Результаты поиска

Содержание TWENTY6 ST-26N

Отзывы:

Бренды по названию

Популярные бренды

Solas TWENTY6 ST-26N, Руководство по установке и эксплуатации

Результаты поиска

Содержание TWENTY6 ST-26N

Отзывы:

Бренды по названию

Популярные бренды