Solas TWENTY6 ST-26N Скачать руководство пользователя страница 36

Страница: 36 / 60

SÓLAS

CONTEMPORARY FIRE

ASSEMBLY & INSTALLATION

Installing the Outer Panels
The outer top and bottom panels are secured to the

fireplace mounting plate with sheet metal screws. All

other screws are philips head machine screws.
1. Install the outer top panel first. Align the three holes

along the rear edge of the panel with pilot holes along

the top edge of the fireplace mounting plate. Insert and

tighten the three sheet metal screws. A magnetic nut

driver is helpful.

2. Install the outer left side panel next. Align the three holes

along the rear edge of the panel with the PEM nuts

along the edge of the fireplace mounting plate. Insert the

three philips head screws but do not fully tighten.

3. Locate the fastener hole at the top front edge of the

outer left side panel and align with the PEM nut in the

front of the top panel. Insert the philips head screw.

4. Make sure the edges of the panel are aligned with the

edges of the top outer panel and mounting plate and

tighten all four philips head screws.

5. Position the outer right side panel so it aligns with the

three PEM nuts on the mounting plate and the front

PEM nut on the top panel. Align the rear and outer top

panel edges with the adjoining parts and insert and

tighten the four philips head screws.

6. Install the outer bottom panel next. Guide the rear

flange on the panel upward until the mounting holes in

the flange line up with the pilot holes in the mounting

plate.

7. Attach the panel to the mounting plate using sheet

metal screws along the back edge of the panel.

Note:

It may make installation of the sheet metal screws

easier if you remove the two lower surround mounting

brackets from the front of the fireplace. A magnetic

nut-driver will also be helpful.

Содержание TWENTY6 ST-26N





























































Результаты поиска

Содержание TWENTY6 ST-26N

Отзывы:

Бренды по названию

Популярные бренды

Solas TWENTY6 ST-26N, Руководство по установке и эксплуатации

Результаты поиска

Содержание TWENTY6 ST-26N

Отзывы:

Бренды по названию

Популярные бренды