manualshive.com logo in svg

Solas TWENTY6 ST-26N, Руководство по установке и эксплуатации

Поделиться
Скачать
Solas TWENTY6 ST-26N Скачать руководство пользователя страница 34

SÓLAS

 CONTEMPORARY FIRE 

34

ASSEMBLY & INSTALLATION

Placing the Burner Glass Media (continued)
4.  Starting at one end, pour the glass media onto 

the burner tray, keeping the pouring spout on the 

poly bag toward the center of the burner to avoid 

spillage of glass pieces over the sides of the burner. 

See the adjacent photos.

5.  Once you have poured all of the glass burner media 

into the burner tray, carefully smooth the glass pieces 

out so they have a uniform depth over the entire 

surface of the burner. When the burner glass media 

is properly placed, it should look like the adjacent 

photos.

6.  NOTE: If a few pieces of glass escape over the edges 

of the burner tray during installation, it is not a problem. 

They will simply land in the area below the burner and 

will do no harm.

 Relief Door Installation
1.   The top relief doors are shipped separate from the 

fireplace and must be installed on the top of the firebox 

at this point in the installation. 

NOTE: The relief doors 

include a gasket that covers the full bottom surface. 

Use care in handling the relief door to avoid damage 

to the gasket material.

2.  The first image shows the relief openings and relief 

door retainers.

3.  Each relief door includes line-up tabs that correspond 

to slotted retainers on the firebox.

4.  Tip the relief door enough to allow the rear line-up tab 

to engage the rear retainer slot. Refer to the second 

image.

5.  Rotate the front edge of each relief door so they line-

up over front retainers.

6.  Gently spring the front forward so it will allow the relief 

door front line-up tab to engage on the retainer. Refer 

to the first image on the top of the next page.

7.  The relief door should be able to move up and down 

freely on the retainers if properly installed.

8.  When the relief door installation is complete, the door 

should be in the full down position. Refer to the second 

image on the top of the next page.

Relief Door Rear Tab 

Engaged with Rear 

Retainer

Relief Door

Front Tab

Retainers

Relief Openings

Burner Glass Media partially installed

Burner Glass Media fully installed

Содержание TWENTY6 ST-26N





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды