manualshive.com logo in svg

Solas TWENTY6 ST-26N, Руководство по установке и эксплуатации

Поделиться
Скачать
Solas TWENTY6 ST-26N Скачать руководство пользователя страница 25

solasfires.com

25

ASSEMBLY & INSTALLATION

Installing the Fireplace Mounting Plate on the Wall
1.  The fireplace mounting plate is attached to the wall 

structure using four 1/4” X 1 1/2” long lag bolts and large 

diameter washers that are provided with the fireplace. 

It is important to use the included hardware as the full 

weight of the fireplace is supported by the mounting 

plate.

2.  Drill a 5/32” diameter pilot hole at each of the mounting 

hole locations that you marked using the template. The 

pilot holes should be the full depth of the lag bolts. Be 

sure that there is solid wood at each mounting location. 

If not, the wall should be reconstructed to provide the 

needed support. 

 

 

 

 

 

 

 

 

 

 

 

 

3.  Before the mounting plate can be lagged to the wall 

the two tabbed sections of the telescoping vent pipe 

heat shields that you set aside earlier must be attached 

to the mounting plate. Each heat shield half is held in 

place with three sheet metal screws (provided). The 

inner shield half (smaller diameter) is installed from the 

front of the mounting plate. Slide the inner heat shield 

half through the vent pipe opening in the mounting 

plate. Align the three tabs with the pilot holes in the 

mounting plate (as shown in the adjacent photo) and 

install the three screws. 

4.  The outer vent pipe heat shield half (larger diameter) 

is installed on the rear of the mounting plate. Slip the 

outer shield half over the inner shield and align and 

install the three screws. See photo below. 

5.  The fireplace mounting plate is now ready to be lagged 

to the wall structure.

6.  With a helper pick up and align the mounting plate over 

the gas supply line and line up with the four mounting 

lag bolt pilot holes. These holes are recessed.  

 

 

 

 

 

 

 

 

 

 

 

 

 

bosses. Use either the 16” or 24” on center holes 

depending on the construction of the wall. 

Mounting Plate Front

4 Lag Bolt Hole Locations

Outer Vent Pipe Shield 

(Larger Diameter, install on the 

backside of the Mounting Plate)

Inner Vent Pipe Shield 

(Smaller Diameter, install on the 

front of the Mounting Plate)

Содержание TWENTY6 ST-26N





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды