manualshive.com logo in svg

Solas TWENTY6 ST-26N, Руководство по установке и эксплуатации

Поделиться
Скачать
Solas TWENTY6 ST-26N Скачать руководство пользователя страница 23

solasfires.com

23

ASSEMBLY & INSTALLATION

Vent Pass-Through (Parallel Wall Installation on an 

Outside Wall)

1.  An unobstructed wall pass-through is required to allow 

for a safe installation of the fireplace vent components. 

This will necessitate removal of a portion of the interior 

wall covering (e.g., sheetrock or plaster and lath), outer 

wall sheathing and outer wall covering and any adjacent 

internal wall materials (like insulation).

2.  Use a long pilot drill (1/8” diameter) that is held square 

and level to the inside wall to transfer the vent pass-

through center location from the inner wall covering 

through to the outer wall sheathing and outer wall 

covering. 

    

    

3.  Carefully cut the inner wall covering along the template 

line and remove the circular wall piece. 

 

 

Note: It is imperative to note the location of 

any plumbing or electrical wiring in the wall 

before beginning the installation process. 

Consult a plumber or an electrician if there 

is any doubt about the location of utilities. 

4.  Carefully cut the gas supply opening, identified on 

the template.

    

    
5.  Remove any insulation materials from wall in the area 

defined by the pass-through hole.

Содержание TWENTY6 ST-26N





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды