manualshive.com logo in svg

SolarEdge RESU10H Prime Series, Руководство по установке

Поделиться
Скачать
SolarEdge RESU10H Prime Series Скачать руководство пользователя страница 65

Ethernet cable specifications:

Cable type – a shielded CAT6 Ethernet cable

Maximum distance between the inverter and the router – 100 m/ 330 ft. 

NOTE

If using a cable longer than 10 m / 33 ft in areas where there is 

a risk of induced voltage surges by lightning, it is recommend 

to use external surge protection devices.

For details refer to: 

https://www.solaredge.com/sites/default/files/overvoltage_

surge_protection_na.pdf

. 

To connect the Ethernet cable:

 1.  Remove the invertercover as described above.

 2.  Open Communication Gland 1.

CAUTION!

The gland includes a rubber waterproof fitting, which should be used to 
ensure proper sealing.

ATTENTION!

Le cote interne du gland contient une rondelle qui doit être utilisée pour une 
bonne étancheïté.

 3.  Remove the plastic seal from one of the large openings.

 4.  Remove the rubber fitting from the gland and insert the CAT6 cable through the 

gland and through the gland opening in the inverter.

 5.  Push the cable into the cut opening of the rubber fitting.

 

Single Phase Energy Hub Inverter with Prism Technology MAN-01-00842-1.3

64

   Creating an Ethernet (LAN) Connection

Содержание RESU10H Prime Series


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды