Sofarsolar HYD 10KTL-3PH Скачать руководство пользователя страница 88

Страница: 88 / 128

COMMISSIONING THE INVERTER

HYD 5K...20KTL-3PH

Battery Address: 00 for the 1

battery, 01 for the 2

battery etc.

The

default operating mode is the Self-use Mode.

EPS Mode, Unbalanced Support, Anti-Reflux Mode, IV-Curve Scan

and Logic interface are disabled.

6.4.1

Configuring the battery setup

The HYD 5 ... 8KTL-3PH models have one battery input (max. current

25 A). The HYD 10 ... 20KTL-3PH models have two battery inputs

(max. current 25 A / 25 A).

Battery inputs can be connected and set in parallel mode to reach 50

A / 70 A.

6.4.2

Configuring Parallel Inverter System

To increase the system's EPS and grid power, the HYD 5 ... 20KTL-

3PH can be parallelly connected at the Grid port and the EPS port.

For the communication setup, please follow the following steps:

Set the Master unit

Set the Slave units

Содержание HYD 10KTL-3PH

































































































































Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы:

Sofarsolar HYD 10KTL-3PH, Инструкция по установке и эксплуатации, Страница: 88 / 128

Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы: