Sofarsolar HYD 10KTL-3PH Скачать руководство пользователя страница 121

Страница: 121 / 128

TROUBLESHOOTING HANDLING

HYD 5K...20KTL-3PH

121

ID147

BluetoothFault

Bluetooth error

Check the Bluetooth

connection of the inverter.

ID148

RTCFault

RTC clock failure

Internal error of the

inverter. Switch off the

inverter, wait 5 minutes

and then switch the unit

back on.

If the error persists,

contact technical support.

ID149

CommEEPROMFault

EEPROM error of

the communication

card

ID150

FlashFault

Communication

card FLASH error

ID152

SafetyVerFrauIt

ID153

SciCommLose(DC)

SCI communication

error (DC)

ID154

SciCommLose(AC)

SCI communication

error (AC)

ID155

SciCommLose(Fuse)

SCI communication

error (fuse)

ID156

SoftVerError

Inconsistent

software versions

Download the latest

firmware from the website

and launch the software

update. If the error

persists, contact technical

support.

ID157

BMSCommunicatonFault

(BMS 1)

Lithium battery

communication

error

Make sure your battery is

compatible with the

inverter.

CAN communication is

recommended. Check the

communication line or the

connection of the battery

and the inverter for errors.

Содержание HYD 10KTL-3PH

































































































































Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы:

Sofarsolar HYD 10KTL-3PH, Инструкция по установке и эксплуатации, Страница: 121 / 128

Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы: