Sofarsolar HYD 10KTL-3PH Скачать руководство пользователя страница 112

Страница: 112 / 128

TROUBLESHOOTING HANDLING

112

HYD 5K...20KTL-3PH

repeatedly, contact

technical support to

adjust the voltage and

frequency limits after

obtaining approval from

the local power grid

operator.

ID005

GFCI

Earth fault

If the error occurs

occasionally, it may be

due to external factors.

The inverter will

automatically return to

normal operation. If the

error occurs frequently

and lasts for a long time,

check whether the

insulation resistance

between the PV generator

and earth (ground) is too

low and check the

insulation of the PV

cables.

ID006

OVRT fault

OVRT function is

faulty

ID006-041 are internal

faults of the inverter. Turn

the DC switch OFF, wait 5

minutes and then turn the

DC switch ON. Check

whether the error has

been cleared. If not,

please contact the

technical support.

ID007

LVRT fault

LVRT function is

faulty

ID008

IslandFault

Island protection

fault

ID009

GridOVPInstant1

Transient

overvoltage of

mains voltage 1

Содержание HYD 10KTL-3PH

































































































































Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы:

Sofarsolar HYD 10KTL-3PH, Инструкция по установке и эксплуатации, Страница: 112 / 128

Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы: