Sofarsolar HYD 10KTL-3PH Скачать руководство пользователя страница 61

Страница: 61 / 128

ELECTRICAL CONNECTIONS

HYD 5K...20KTL-3PH

5.9.3

Energy meter

NOTE

•

The energy meter DTSU666 0.05-1.5(6) A and (HY94C5-

200) CTs are supplied with the inverter.

•

Max. current input energy meter: 5 A

•

Max. measured current: 200 A (Ratio: 40:1)

The integrated energy management functions integrated of the HYD

5K...20KTL-3PH require to measure the power flow at the point of grid

interconnection. There are different system configurations possible. It

can be measured using CTs (up to 300 A), or with direct connection

(up to 80 A).

Please refer to below table for the PIN assignments for the RS485

connection between the inverter and the energy meter.

Inverter COM Port Pin Function

Meter Pin

Pin 5

RS485+ (A2)

Pin 24

Pin 6

RS485- (B2)

Pin 25

NOTE

•

Use the shielded twisted pair cable

•

The copper outer diameter should be more than 0.5 mm²

•

Keep away from power cables or other electric fields

•

Maximum distance is 1200 meters

Содержание HYD 10KTL-3PH

































































































































Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы:

Sofarsolar HYD 10KTL-3PH, Инструкция по установке и эксплуатации, Страница: 61 / 128

Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы: