Sofarsolar HYD 10KTL-3PH Скачать руководство пользователя страница 86

Страница: 86 / 128

COMMISSIONING THE INVERTER

HYD 5K...20KTL-3PH

For lithium battery, please ensure that the communication cable

has been correctly connected.

For the lead-acid battery, please ensure that the NTC wire has

been correctly connected.

6.3

Starting the inverter

Please follow below steps to switch the inverter ON.

Make sure there's no power generation in inverter's phase.

Turn ON DC switch.

Switch ON the battery. Turn ON DC isolator between battery &

inverter.

Turn ON AC circuit breaker between the inverter GRID port &

GRID.

Turn ON AC circuit breaker between the inverter LOAD port &

critical load.

Inverter should start to operate now.

6.4

Initial setup

You need to set the following parameters before inverter starts to

operate.

Parameter

Note

1) Language setting

The default is English

2) System time setting

If you are connected to the server

or using the App, the time is set to

the local time automatically

Содержание HYD 10KTL-3PH

































































































































Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы:

Sofarsolar HYD 10KTL-3PH, Инструкция по установке и эксплуатации, Страница: 86 / 128

Результаты поиска

Содержание HYD 10KTL-3PH

Отзывы: