manualshive.com logo in svg

Sofarsolar HYD 10KTL-3PH, Инструкция по установке и эксплуатации, Страница: 115 / 128

Поделиться
Скачать
Sofarsolar HYD 10KTL-3PH Скачать руководство пользователя страница 115

 

TROUBLESHOOTING HANDLING 

HYD 5K...20KTL-3PH 

115 

ID049 

TempFault_Bat 

Battery 

temperature error 

Make sure that the 

battery does not get too 

hot. 

 

Check that the 

temperature sensor has 

been correctly connected 

to the battery. 

ID050 

TempFault_HeatSink1 

Temperature error 

heat sink 1 

Make sure that the 

inverter has been 

installed in a cool and 

well-ventilated place 

without direct sunlight. 

 

Make sure the inverter is 

installed vertically and the 

ambient temperature is 

below the inverter's 

temperature limit. 

ID051 

TempFault_HeatSink2 

Temperature error 

heat sink 2 

ID052 

TempFault_HeatSin3 

Heat sink 

temperature error 

3 

ID053 

TempFault_HeatSink4 

Temperature error 

heat sink 4 

ID054 

TempFault_HeatSin5 

Temperature error 

heat sink 5 

ID055 

TempFault_HeatSin6 

Temperature error 

heat sink 6 

ID057 

TempFault_Env1 

Temperature error 

ambient 

temperature 1 

ID058 

TempFault_Env2 

Temperature error 

ambient 

temperature 2 

ID059 

TempFault_Inv1 

Temperature error 

module 1 

ID060 

TempFault_Inv2 

Temperature error 

module 2 

Содержание HYD 10KTL-3PH

































































































































Отзывы:

Нет отзывов