SnowEx 6800LT Скачать руководство пользователя страница 77

Страница: 77 / 92

Lit. No. 89451, Rev. 05

May 15, 2022

MAINTENANCE

•

Trip Spring Adjustment (Straight Blade,

SPEEDWING™, and POWER PLOW™

snowplows):

To adjust trip spring tension,

adjust the eyebolts located at the top of the

blade. Loosen the locknut (nut closest to the

spring), and tighten the adjusting nut (nut

farthest from the spring) until the coils begin to

separate. When tension is properly adjusted, a

sheet of paper should pass between the second

and third coils. When the proper tension is

reached, tighten the locknut.

•

Blade Finish:

If the powder-coat finish is

nicked or scratched, repair the surface and

paint with SnowEx

gray or gloss black paint

(available in aerosol or quart can).

GREASING HDV™ PIVOT PIN HINGE

Using a rubber-tipped seal-off coupler, apply a

good quality multipurpose grease at the five

grease points along the center pivot pin hinge.

Grease the hinge at the beginning of the

snowplow season. Reapply as needed during

the season and before putting the snowplow in

storage.

Grease

Points

Содержание 6800LT





























































































Результаты поиска

Содержание 6800LT

Отзывы:

Похожие инструкции для 6800LT

Бренды по названию

Популярные бренды

SnowEx 6800LT, Руководство пользователя

Результаты поиска

Содержание 6800LT

Отзывы:

Похожие инструкции для 6800LT

Бренды по названию

Популярные бренды