1.-
Speed Vitesse Velocidad Velocit
à
Snelheid Absaugleistung
Ñêîðîñòü
Velocidade Hastighet
I
Low
Moyenne
Baja
Bassa
Laag
Leistungsstufe
Íèçêàÿ
Baixa
L
å
g
II
High
Maximum
Alta
Alta
Hoog
Intensivstufe
Âûñîêàÿ
Alta
H
ö
g
+
Intensive
Intensive
Intensiva
Intensa
Intensief
Intensiv
Èíòåíñèâíàÿ
Intensiva
Intensiv
Light
Lumi
è
re
Luz
Luce
Licht
Beleuchtung
Îñâåùåíèå
Luz
Lampa
On
Off
Allum
é
Eteint
Encendido
Apagado
Accesa
Spenta
Aan
Uit
Ein
Aus
Âêëþ÷åíî
Îòêëþ÷åíî
Acesa
Desligada
P
å
Av
2.-
Instructions for use
By pushing buttons shown in the figure 1,
you will be able to control the functions of the
extractor
Two
achieve
better
extraction,
we
recommend switching on the extractor a few
minutes before starting to cook (3 - 5
minutes) so that the air flow is continuous
and stable when extracting the fumes.
Likewise, keep the extractor switched on for
a few minutes when cooking is complete to
allow all fumes and odours to be expelled.
Cleaning and maintenance
Before carrying out any cleaning or
maintenance activities, ensure that the
extractor is disconnected from the mains.
To carry out cleaning and maintenance,
follow the Safety Instructions.
Filter cleaning
To remove the filters from their locations
release the anchoring points. Clean the filter,
either by putting it in the dishwasher (see
notes) or leaving it standing in hot water to
simplify the removal of grease or, if wished,
by means of special sprays (protecting the
non metallic parts). Once clean, leave it to
dry.
Notes:
cleaning in the dishwasher with
aggressive detergents may darken the
surface of metallic parts, without this
affecting its gas retaining properties.
N.B.
The filter must be cleaned at least once
a month depending on how often the
extractor is used. It must be remembered
that grease accumulates in the extractor
when cooking, whether it is switched on or
not.
Cleaning of the extractor body
The use of warm (40
º
C approx.) soapy water
is recommended. A cloth moistened in this
water is used for cleaning the extractor,
paying special attention to the grids.
Afterwards, dry it using a lint-free cloth.
Note:
*
Never use metallic scouring pads or
abrasive products that could damage the
surface.
* Do not use scrapers with metallic surfaces
such as knives, scissors etc.
Active charcoal filter
* To install the charcoal filters it is necessary
to firstly remove the metallic grease filters.
* In order to fix them it is necessary to
introduce the rear lips of each filter in the
holes provided for it in the security grid,
turning them upwards until its fixation by
clipping in the front part (Fig.6).
* The carbon filters last from three to six
months
depending
on
the
particular
conditions of use.
* The active carbon filters can neither be
washed nor regenerated. Once they are
exhausted, they must be changed.
* To replace worn out filters with new ones,
remove the old ones in the reverse order to
that of installation
.
Changing Bulbs
* It is important that the mains are
disconnected, and ensure the bulbs that are
to be replaced are not hot.
* Remove the light lens to expose the
extractable lamps.
* The maximum bulbs power is 20W.
Technical Information
(Fig.3)
Dimensions
Width = 600//900 mm
Depth = 300 mm
Height = 353 mm
Electrical characteristics:
REFER TO RATING PLATE
A
C
D
E
B
A
