Slendertone ABS6 Скачать руководство пользователя страница 4

Страница: 4 / 28

Step 1 - Charge the battery.

Insert your charger into an electrical outlet

and then connect your controller to it (Fig. a). It may take approximately
2-3 hours to fully charge the battery. Your controller is fully charged when
all three sections of the battery icon are full. The battery icon will flash
when the battery is low and needs to be recharged.

NOTE

Do not leave your controller connected to the charger when the

battery is fully charged.

Step 2 - Connect the controller to the belt.

The controller and belt

must be connected for

SLENDERTONE ABS

6 to work. Place the belt on a flat

surface with the gold stitching facing you. ‘Click’ the controller connector
into the belt connector as shown in Fig. b.

MPORTANT

Make sure the controller and belt are connected correctly or

your

SLENDERTONE ABS

6 will not work - this is a safety feature.

Step 3 - Remove the covers from the patterned side of the GelPads and place them on the belt.

Turn the belt over so that the 3 silver studs are facing upwards. Remove the three adhesive
GelPads from their pack. There is 1 large square GelPad and 2 smaller oval GelPads. One side

of each GelPad has a

grid pattern

on it while the other side is

black

(i)

Remove the covers from the

patterned side

the large GelPad.

(ii)

Place the

patterned side

of this GelPad over the

middle stud and between the white lines.

(iii)

Now remove the covers from the

patterned side

of the two smaller GelPads.

(iv)

Place the

patterned side

of the smaller GelPads

firmly onto the belt, either side of the large GelPad.

(v)

The location of the smaller GelPads depends on

your waist size. In the example below, the smaller GelPads are placed close to the large, cen-
tral GelPad. This is for a user whose waist size is 24"-31". Use the sizing guidelines below to
help you choose your correct
GelPad location.

IMPORTANT

Before you progress, make sure that all three silver studs are completely covered by the
GelPads. Press the edges of all three GelPads firmly onto the belt before use.

ONTROLS

1. On/Off Button ( )

Press and hold this button for 2 seconds to turn
your controller on or off. You may also pause the
exercise by briefly pressing this button.

2. Increase Training Intensity ( )

Press and hold these buttons to increase the
intensity of the exercise. The right-hand button
controls the right-hand side of your belt. The
left-hand button controls the left-hand side.

3. Decrease Training Intensity ( )

Press and hold these buttons to decrease the
intensity of the exercise on either side of the belt.

4. Program Button ( P )

Press this button to select the toning program you wish to use. There are 7 programs in total,
which are explained later in this manual (page 10).

5. Information Button (

)

Press this button to see your training information, such as the maximum intensity for your current
or last session and the number of sessions you have completed.

ISPLAY

Training intensity from the left-hand side of the belt.

Training intensity from the right-hand side of the belt.

Counts down the time left in the current session in minutes and seconds. Also used to
display error messages (see page 12).

Appears when the exercise has been paused (you must press the on/off button briefly to
restart the exercise).

Indicates that the sound is off.

Keylock is active - you cannot change the intensity levels or the program accidentally.

This symbol indicates a poor contact between the controller and the belt or between the
GelPads and the skin (see page 14 for more details).

Shows the battery power remaining.

Number of sessions completed.

Shows the program currently running (1 - 7).

This symbol appears during each contraction phase.