SKYZER TECHNOLOGIES
PAGE 22 OF 38
INGENICO I5100 VERSION 6.0 CONFIGURATION GUIDE
Version 1.0
TCP-IP (Broadband) Configuration
24.0
PRIMARY
PRIMARY
PRIMARY
PRIMARY
HOST IP ADDRESS
HOST IP ADDRESS
HOST IP ADDRESS
HOST IP ADDRESS
117.120.34.110
117.120.34.110
117.120.34.110
117.120.34.110
This parameter specifies the Primary Host IP Address. By default, it is set to
117.120.34.110
.
Press
ENTER.
25.0
SECONDARY
SECONDARY
SECONDARY
SECONDARY
HOST IP ADDRESS
HOST IP ADDRESS
HOST IP ADDRESS
HOST IP ADDRESS
117.120.32.110
117.120.32.110
117.120.32.110
117.120.32.110
This parameter specifies the Secondary Host IP Address. By default, it is set to
117.120.32.110
.
Press
ENTER.
26.0
ENAB
ENAB
ENAB
ENABLE DHCP Y/N
LE DHCP Y/N
LE DHCP Y/N
LE DHCP Y/N
1
1
1
1-
-
-
-YES 2
YES 2
YES 2
YES 2-
-
-
-NO
NO
NO
NO
To enable the DHCP (Dynamic Host Configuration Protocol), press
1
followed by the
ENTER
and proceed with step 31.0.
Note: By default 1-YES is always selected.
If a site has no DHCP enabled on their router, then proceed with step 27.0
27.0
ENABLE DHCP Y/N
ENABLE DHCP Y/N
ENABLE DHCP Y/N
ENABLE DHCP Y/N
1
1
1
1-
-
-
-YES 2
YES 2
YES 2
YES 2-
-
-
-NO
NO
NO
NO
To disable the DHCP (Dynamic Host Configuration Protocol), press
2
followed by the
ENTER
and proceed with step 28.0.
NOTE: When configuring the terminal for Static IP address, ensure to
obtain the IP address, subnet mask and default gateway IP address from
your ISP (Internet Service Provider) for connectivity with the ETSL
network.
28.0
TERM IP ADDRESS
TERM IP ADDRESS
TERM IP ADDRESS
TERM IP ADDRESS
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Enter in the static IP address for the terminal.
Example: 192.10.1.14
Note:
Press the
FUNC
key to insert a dot in between numbers.
29.0
SUBNET MASK
SUBNET MASK
SUBNET MASK
SUBNET MASK
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Enter in the subnet mask for the static IP address.
Example: 255.255.255.0
30.0
GATEWAY IP ADDR
GATEWAY IP ADDR
GATEWAY IP ADDR
GATEWAY IP ADDR
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Enter in the gateway IP address to forward the packets from.
Example: 192.10.1.1
31.0
SAVE CONFIG Y/N
SAVE CONFIG Y/N
SAVE CONFIG Y/N
SAVE CONFIG Y/N
Terminal prompts to save configuration. Press
ENTER
to save configuration on the
terminal or press
CLEAR
to exit and return to idle screen.
32.0
START TCP
START TCP
START TCP
START TCP-
-
-
-IP Y/N?
IP Y/N?
IP Y/N?
IP Y/N?
Terminal prompts to start TCP-IP (broadband) connection. Press
ENTER
to start
TCP-IP connectivity or
CLEAR
to exit without starting TCP-IP.