Sisu Commercial Products Sleeptight 800 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 41

background image

The Sleeptight 800 is designed for indoor use only. It is intended for use in providing portable,
temporary heat to buildings under construction, alteration or repair. Adequate ventilation must
be provided while heater is operating. Combustible solids, such as building materials, paper or
cardboard must be kept at the minimum distance from the heater as shown in the table below.
Never use this heater in spaces which do or may contain volatile or airborne combustibles,
or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
Adequate building relief must be provided so as to not over pressurize the building when this
heater is operating at its rated capacity.

OMNI Test Laboratories certified to ANSI Z83.7-2017•CSA 2.14-2.017 Gas-Fired Construction Heater

Gases:

Propane

Capacity:

80,000 Btu/Hr maximum

Blower:

1600

CFM

Electrical:

115V, 60Hz, 1Ph, 4.7 Amps starting, 3.2 Amps continuous

Min Amb Temp:

-20 Degrees F

Max Amb Temp:

140 Degrees F

Min Gas Supply Press:

11 in. W.C.

Max Gas Supply Press:

13.5 in. W.C.

Burner Manifold Press:

8 in. W.C.

Manufacturer:

L.B. White Co., LLC. Onalaska, WI

SYSTEM DESCRIPTION

SPECIFICATIONS

6

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS

Top

24 inches

Outlet side

24 inches

Inlet Side

24 inches

Front/Back

24 inches

«
...
5
6
7
8
9
...
»

Содержание Sleeptight 800










































Отзывы:

Нет отзывов

Похожие инструкции для Sleeptight 800

Бренд: Jandy Страницы: 48

Бренд: EUROM Страницы: 120

Бренд: ESBE Страницы: 28

Rocco FBFL**RN3

Бренд: Flavel Страницы: 32

Бренд: Calorex Страницы: 2

Бренд: Lynx Страницы: 23

Бренд: PAMAPIC Страницы: 16

Бренд: Harbor Freight Tools Страницы: 10

Trumatic S 2200

Бренд: Truma Страницы: 2

LNVx CCF Series

Бренд: Powrmatic Страницы: 48

Бренд: STIEBEL ELTRON Страницы: 40

Бренд: OMEGA AIR Страницы: 25

Бренд: Zephir Страницы: 29

Copper Cricket 1B

Бренд: Sage Advance Corp Страницы: 67

Бренд: Dimplex Страницы: 12

Бренд: Velleman Страницы: 55

Бренд: GMI Страницы: 5

Бренд: Accorroni Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды