Sisu Commercial Products Sleeptight 800 Скачать руководство пользователя страница 35

Страница: 35 / 41

B. Gauge Installation

1. Locate the inlet and outlet pressure taps, see Figure below. Loosen the pressure tap screw using a 3/32 Allen

key.

2. Securely connect a pressure gauge to each pressure tap.

3. Open the fuel supply valves to the heater and reconnect the heater electrical supply.

4. Start the heater

C. Reading Pressures

1. With the heater operating, the pressure gauges should read the pressures specified on the dataplate .

2. If the readings at the inlet and outlet pressure gauges agree with that specified on the dataplate, then no

further checking or adjustment is required. Proceed to section D.

3. If the inlet pressure does not agree with that specified on the dataplate, then the regulator controlling gas

pressure to the heater requires adjustment.

4. If the inlet pressure is correct and the burner manifold pressure does not agree with that specifed on the

dataplate, then the gas control valve’s internal pressure regulator requires adjustment. See previous figure
for regulator location.

5. Remove the regulator adjustment cap screw and turn the internal screw clockwise to increase or counter

clockwise to decrease to the desired pressure.

6. Install the regulator cap back onto the gas valve when completed. Tighten securely.

Outlet
Pressure
Tap

Regulator
Adjustment Cap

Inlet Pressure Tap

Содержание Sleeptight 800










































Результаты поиска

Содержание Sleeptight 800

Отзывы:

Бренды по названию

Популярные бренды

Sisu Commercial Products Sleeptight 800, Инструкция и руководство пользователя

Результаты поиска

Содержание Sleeptight 800

Отзывы:

Бренды по названию

Популярные бренды