8KS
8KBS
3 Safety
Version 08/2012, Rev. 1.6 of 04/02/2014 • sb
19
Translation of the original operating manual
Pos: 44 / 100 Sigma /100 BA Ze ntrifu gen (Sta nda rdm odul e)/0 30 Sich erh eit/0 30- 0060 Siche rheit shinweis e- --- --- -- --- -- --- -- --- --- -- --- -- --- --- -- --- -- --- -- --- --- -- --- @ 7\ mo d_13 063 035 636 43_ 68.d ocx @ 432 96 @ 2 @ 1
3.6 Safety instructions
Pos: 45 / 100 Sigma /100 BA Ze ntrifu gen (Sta nda rdm odul e)/0 30 Sich erh eit/0 30- 0060 -00 10 Elektrisc he Sich erh eit @ 7\mo d_1 306 303 612 969 _68. docx @ 43 303 @ 3 @ 1
3.6.1 Electrical safety
To reduce the risk of electrical shock, the centrifuge uses a three-wire
electrical cord and plug to connect the equipment to earth-ground. To
preserve this safety feature:
DANGER
• Ensure that the wall socket is properly wired and grounded.
• Check that the mains voltage agrees with the nominal voltage listed on
the name plate.
• Do not place vessels containing liquid on the centrifuge lid or within the
safety distance of 30 cm around the centrifuge. Spilled liquids may get
into the centrifuge and damage electrical or mechanical components.
• Work on the power supply system must only be performed by certified
electricians.
• Inspect the electrical equipment of the unit regularly. Defects such as
loose or burnt cables must be eliminated immediately.
Pos: 46 / 010 Unive rsalm odul e/ L ee rzeile @ 0\ mod _120 211 624 450 0_0. docx @ 11 4 @ @ 1
Pos: 47 / 100 Sigma /100 BA Ze ntrifu gen (Sta nda rdm odul e)/0 30 Sich erh eit/0 30- 0060 -00 20 Mec hanis che Sich erh eit ( au ßer 1-1 6/1 -16K) @ 7\ mo d_13 063 026 663 34_ 68.d ocx @ 432 61 @ 3 @ 1
3.6.2 Mechanical safety
In order to ensure the safe operation of the centrifuge, observe the
following:
WARNING
• Do not open the lid when the rotor is in motion!
• Do not reach into the rotor chamber when the rotor is in motion!
• Do not use the centrifuge if it was installed incorrectly.
• Do not use the centrifuge without panels.
• Do not use the centrifuge if the rotors and inserts show signs of
corrosion or other defects.
• Only use the centrifuge with rotors and accessories that have been
approved by the manufacturer. In case of doubt, contact the
manufacturer (see chapter 7.3 - "
Service contact
").
• Do not hold your fingers between the lid and the housing when closing
the lid. Risk of crushing!
• Defective lid relieving devices could cause the centrifuge lid to fall
(contact the service department, if necessary). Risk of crushing!
• Do not hit or move the centrifuge during its operation.
• Do not lean against or rest on the centrifuge during its operation.
• Do not spin any substances that could damage the material of the
rotors and buckets of the centrifuge in any way. Highly corrosive
substances, for example, damage the material and affect the
mechanical strength of the rotors and buckets.
• Stop the centrifuge immediately in the event of a malfunction. Eliminate
the malfunction (see chapter 7 - "
Malfunctions and error correction
")
or inform the service department of Sigma Laborzentrifugen GmbH
(see chapter 7.3 - "
Service contact
").
• Ensure that all repairs are performed only by authorised and
specialised personnel.
