Sierra InnovaMass 240i Series Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 115

Sierra InnovaMass 240i Series Скачать руководство пользователя страница 67

67

Process Pressure Sub-Menu: Process Pressure

Use this menu to enter the process pressure.

The “Process Pressure Sub-Menu: Process Pressure” is only applicable in V
and VT units, VTP will have this real time.

As in previous examples, use the



buttons to enter the desired value, and the enter key



to save the value.

Process pressure is used by the instruments Raptor II operating system to improve gas property
calculations. Gas properties have a very slight dependence on pressure, so if process pressure
changes appreciably over time this value should be updated to reflect process conditions.

The process pressure can also be simulated in the “Diagnostics Sub-menu.”

The units of the pressure in this menu are the same as what was set in the previous menu. In the
example above, the units are 14.700000 Psia since this is what was set in the pressure units sub-
menu.

This concludes our review of the Process Pressure menu. Press





to go to the Temperature Units

menu or exit



to climb back up to the main menu.

This concludes our review of the Process Pressure Sub-Menu. Press the exit



climb back up to

the main menu.

Totalizer (Sub-Menu)

The Totalizer Sub-Menu controls all aspects of the totalizer function.

Watch Video Tutorial

– a video tutorial for this function called “Local

Display Interface Navigation” is available on the USB flash drive provided
in the product shipment.

Navigate to the Totalizer (Sub-Menu) screen. Use Table 10 below for guidance. You will see this
screen:

Process Pressure

14.700000

Totalizer

(Sub-Menu)

«
...
65
66
67
68
69
...
»

Содержание InnovaMass 240i Series




















































































































Отзывы:

Нет отзывов