Sierra InnovaMass 240i Series Скачать руководство пользователя страница 52

Страница: 52 / 115

The sensor has failed.

Solution:



Check the Low/High sub-menu (see Table 8) to see if the meter’s pressure limits
have been exceeded.



The meter may need to be

returned to the factory

. If this is not immediately

possible, pressure may be simulated in the simulate submenu.

SD Card Issues

240i/241i meters have one SD Card for storing meter data.

Possible Cause of Error Code

The SD Card is missing.

Solution:



Replace the SD Card if available.



Contact Sierra for a replacement SD Card.

The SD Card is damaged.

Solution:



Contact Sierra for replacement card

UART Issues

240i/241i meters have multiple Universal Asynchronous Receiver/Transmitters (UART) for
communications (ex. USB).

Possible Cause of Error Code

UART is malfunctioning.

Solution:



Contact Sierra for remote troubleshooting.



The meter may need to be

returned to the factory

UART is damaged/disconnected.

Solution:



The meter may need to be

returned to the factory

MCU Voltage Issues

240i/241i meters have a Microcontroller (MCU) with a nominal voltage range.

Possible Cause of Error Code

Содержание InnovaMass 240i Series




















































































































Результаты поиска

Содержание InnovaMass 240i Series

Отзывы:

Sierra InnovaMass 240i Series, Инструкция по эксплуатации, Страница: 52 / 115

Результаты поиска

Содержание InnovaMass 240i Series

Отзывы: