Sierra InnovaMass 240i Series Скачать руководство пользователя страница 101

Страница: 101 / 115

101

scfm

Standard cubic feet per minute (flow rate converted to standard
conditions, as shipped 14.696 psia and 59° F). User definable.

Shedder Bar

A non-streamlined body placed into a flow stream to create vortices.
Also called a Bluff Body.

Strouhal Number (St)

A dimensionless number equal to the frequency

of vortices created by a bluff body times the width of the bluff body
divided by the velocity of the flowing fluid (i.e., St = fd/V). This is an
important number for vortex flow meters because it relates the vortex
frequency to the fluid velocity.

Totalizer

An electronic counter which records the total accumulated flow over
a certain range of time.

Traverse

The act of moving a measuring point across the width of a flow
channel.

U V W X Y Z

Uncertainty

The closeness of agreement between the result of a measurement and
the true value of the measurement.

Velocity or voltage

VAC

Volts, alternating current

VDC

Volts, direct current

VORTEX

An eddy of fluid

Содержание InnovaMass 240i Series




















































































































Результаты поиска

Содержание InnovaMass 240i Series

Отзывы:

Sierra InnovaMass 240i Series, Инструкция по эксплуатации, Страница: 101 / 115

Результаты поиска

Содержание InnovaMass 240i Series

Отзывы: