Sierra InnovaMass 240i Series Скачать руководство пользователя страница 53

Страница: 53 / 115

MCU is malfunctioning.

Solution:



Contact Sierra for remote troubleshooting.



The meter may need to be

returned to the factory

MCU has failed.

Solution:



The meter may need to be

returned to the factory

Main Board Button Stuck

240i/241i meters have display buttons for navigation and data entry.

Possible Cause of Error Code

Main board button stuck down.

Solution:



Attempt to unstick buttons manually.



Contact Sierra for remote troubleshooting.



The meter may need to be

returned to the factory

Digicomms Fail

240i/241i meters can be ordered with Digital Communications (Hart, Profibus, Foundation
Fieldbus, etc.).

Possible Cause of Error Code

Digital Communications malfunction.

Solution:



Contact Sierra for remote troubleshooting.



The meter may need to be

returned to the factory

. If this is not immediately

possible, output via 4-20 mA, RS232, or USB is available.

Signal Noise

240i/241i meters are sensitive to background noise or vibration in the application environment
(60 Hz/50 Hz from power lines).

Possible Cause of Error Code

Meter Settings may need to be adjusted.

Solution:

Содержание InnovaMass 240i Series




















































































































Результаты поиска

Содержание InnovaMass 240i Series

Отзывы:

Sierra InnovaMass 240i Series, Инструкция по эксплуатации, Страница: 53 / 115

Результаты поиска

Содержание InnovaMass 240i Series

Отзывы: