9 – 36
Modus „Parametereinstellung“
Dieser Modus erlaubt die Einstellung folgender Parameter:
- Lastabwurf
- Lastaufnahme
- Verzögerungszeit Lastabwurf/Lastaufnahme
- Spracheinstellung für Display
VORSICHT
CAUTION
Parametereinstellungen grundsätzlich nur vornehmen, wenn
der Leistungsschalter ausgeschaltet ist.
Eine Veränderung der Parameter bei eingeschaltetem Lei-
stungsschalter kann zu ungewolltem Auslösen des Leistungs-
schalters führen.
Adjust parameters only when the circuit breaker is in the
OPEN position.
If the parameters are modified when the circuit breaker is
CLOSED, the circuit breaker may trip unintentionally.
Um in den Modus „Parametereinstellung“ zu gelangen, folgende
Taste(n) drücken:
Im Modus „Autoscroll“
Angezeigte Screens im Modus „Parametereinstellung“
Screen 1
Einstellung
Lastabwurf
Screen 2
Einstellung
Lastaufnahme
Screen 3
Einstellung
Verzögerungszeit
Lastabwurf / -aufnahme
Screen 4
Einstellung
Sprache Display
Für XXXX kann stehen:
ENGL, DEUT
Screen 5
Parameteränderungen wer-
den durchgeführt,
nach 10 Sekunden Wechsel in
den Modus „Autoscroll“
Parameter Ändern
Lastabwurf..=.0000.A
=+ =-
.und. =Bestätigen
Parameter Ändern
Lastaufnahme=.0000.A
=+ =-
.und. =Bestätigen
Parameter Ändern
tx..........=...00.s
=+ =-
.und. =Bestätigen
Parameter Ändern
Sprache/Lang=...XXXX
=+ =-
.und. =Bestätigen
Parameter werden
geändert
10s warten
"Parameter setting" mode
In this mode, the following parameters can be adjusted:
- load shed
- load restore
- time delay load shed/load restore
- language setting for display
To get to the "Parameter setting" mode, press the following
button:
In the "Autoscroll" mode
Screens displayed in the "Parameter setting" mode
Screen 1
Setting
Load shed
Screen 2
Setting
Load restore
Screen 3
Setting
Time delay
Load shed/load restore
Screen 4
Setting
Display language
XXXX may be ENGL or GERM
Screen 5
Parameter settings in process,
change to "Autoscroll" mode
after 10 seconds
Change Parameters
Load.Shed..=.0000.A
=+ =-
.und. =Confirm
Change Parameters
Load.Restore=.0000.A
=+ =-
.und. =Confirm
Change Parameters
=+ =-
.und. =Confirm
tx..........=...00.s
Change Parameters
=+ =-
.und. =Confirm
Sprache/Lang=...XXXX
Changed.Parameter
being.saved,
wait.10s
Содержание WL Series
