Siemens SITOP PSU3800 12 V/20 A Скачать руководство пользователя страница 18

Страница: 18 / 108

Description, device design, dimension drawing

2.5 Change-over switch

SITOP PSU8200/3800 3ph

Manual, 05.2018, C98130-A7638-A1-6-7629

2.5

Change-over switch

Figure 2-6

Selector switch A/B

The two switches A and B are used to influence the output characteristic:

Switch

OFF

influences the output

characteristic in the

load range

Parallel operation:

"Soft" characteristic curve (see Figure 6-12 Output

characteristic curve 6EP3436-8SB00-0AY0 parallel

operation (Page 65) to Figure 6-19 Output character-

istic 6EP3447-8SB00-0AY0 parallel operation

(Page 67)) for parallel operation of two or more devic-

es: The output voltage falls with increasing output

current (namely, also for the overcurrent pulse!).

This means that for full output current the highest

output voltage can normally no longer be attained.

Single operation:

delivery condition

"Hard" characteristic (see Figure 6-3

Output characteristic curve 6EP3436-

8SB00-0AY0 single operation (Page 61)

to Figure 6-10 Output characteristic

6EP3447-8SB00-0AY0 single operation

(Page 64)) for normal operation (single

operation): The output voltage is inde-

pendent of the output current.

influences the output

characteristic in the

overload range

Latching shutdown:

If the output current rises above the rated value and

above the current limit, the device reduces the output

voltage (see Figure 6-21 Output characteristic curve

6EP3436-8SB00-0AY0 latching shutdown (Page 68)

to Figure 6-28 Output characteristic 6EP3447-8SB00-

0AY0 latching shutdown (Page 70)). If the output

voltage falls below 10/20/30/40 or 44 V, the device

shuts down latching, the red LED lights up. This limit

voltage of 10/20/30/40 V is independent of the output

voltage that has been set. The 'Short-time overload

current' feature is not available in this operating mode.

In order to also be able to charge large capacitances

in this operating mode at the output, non-latching

shutdown is performed during the first ten seconds

after power on. During these first 10 s, the device

responds for overload as if the switch is OFF.

Constant current:

delivery condition

The device reduces the output voltage if

the output current exceeds the rated

value and the current limit. The yellow

LED lights up if the output voltage falls

below 10/20/30/40 or 44 V.

Содержание SITOP PSU3800 12 V/20 A













































































































Результаты поиска

Содержание SITOP PSU3800 12 V/20 A

Отзывы:

Похожие инструкции для SITOP PSU3800 12 V/20 A

Бренды по названию

Популярные бренды

Siemens SITOP PSU3800 12 V/20 A, Руководство пользователя

Результаты поиска

Содержание SITOP PSU3800 12 V/20 A

Отзывы:

Похожие инструкции для SITOP PSU3800 12 V/20 A

Бренды по названию

Популярные бренды