Siemens SITOP PSU3800 12 V/20 A Скачать руководство пользователя страница 25

Страница: 25 / 108

SITOP PSU8200/3800 3ph
Manual, 05.2018, C98130-A7638-A1-6-7629

Mounting/removing

WARNING

Installing the device in a housing or a control cabinet
The SITOP PSU8200/3800 3ph power supply is a built-in device. It must be installed in a

housing or control cabinet, to which only qualified personnel have access.

The device can be mounted in a control cabinet on standard mounting rails (see Chapter

Mechanical system (Page 80))

Mounting
To mount the device, position it with the mounting rail guide at the upper edge of the

standard mounting rail and press down to lock it into place. If it is too difficult to snap them

into place, press slider at the same time, as described under "Removal".

Removal
To remove, pull up the slider using a screwdriver and disengage the device at the bottom

edge of the standard mounting rail. Then you can remove the device from the upper edge of

the standard mounting rail.

Figure 3-1

Mounting/removal (example 6EP3436-8SB00-0AY0)

Содержание SITOP PSU3800 12 V/20 A













































































































Результаты поиска

Содержание SITOP PSU3800 12 V/20 A

Отзывы:

Siemens SITOP PSU3800 12 V/20 A, Руководство пользователя, Страница: 25 / 108

Результаты поиска

Содержание SITOP PSU3800 12 V/20 A

Отзывы: