Siemens SIMATIC RF120C Скачать руководство пользователя страница 54

Страница: 54 / 92

Service and maintenance

5.3 FB error messages

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

Byte

Description

E2h FEh 01h

•

Field interference on the reader

The reader is receiving interference from its environment.
–

External interference field; the field of interference can be verified with the "inductive field

indicator" of the STG

–

The distance between two readers is too short and does not correspond to the configuration

guidelines

–

The connecting cable to the reader is disrupted, too long or does not comply with the

specification

–

MOBY U: Transponder has left the antenna field during communication.

–

MOBY U: Communication between reader and transponder was aborted due to a disruption

(e.g. person/foreign body moving between reader and transponder).

•

Too many transmission errors

The transponder could not receive the command or the write data correctly from the

communications module even after several attempts.
–

The transponder is positioned exactly in the limit area of the transmission window

–

Data transmission to the transponder is being affected by external interference

•

CRC sending error
–

The transponder reports CRC error frequently (transponder is positioned in the limit area of the

reader; transponder and/or reader has a hardware defect)

•

Only during initialization: CRC error on receipt of acknowledgement from transponder (cause as

for field interference on the reader)

•

When formatting, the transponder must be in the transmission window of the reader, otherwise a

timeout error will occur, in other words:
–

The transponder is located exactly in the limit area of the transmission window

–

The transponder is using too much current (defect)

–

Bad FORMAT parameter setting for transponder EEPROM

•

RF600:
–

No free ETSI channel

–

Wrong communications standard selected in the "init_run" command

–

Bad expert parameter

–

Power check of the ETSI wireless profile is incorrect

E2h FEh 02h

•

More transponders are located in the transmission window than can be processed at the same

time by the reader.

•

RF600: Transponder power supply close to limit.
Increase the antenna power or reduce the distance to the transponder.

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды