Siemens SIMATIC RF120C Скачать руководство пользователя страница 5

Страница: 5 / 92

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

Introduction

Purpose of these operating instructions

With the information in these operating instructions, you will be able to commission and

operate the RF120C communications module with a SIMATIC S7-1200 controller.

Basic knowledge required

These operating instructions assume general knowledge of automation engineering and

identification systems.

Scope of the manual

The operating instructions apply to the RF120C communications module.

Note
Validity of the manual for other communications modules
You can also use the function blocks described in the section "Ident instructions (Page 30)"

in the same way for the communications modules RF180C (PROFINET) and ASM 456

(PROFIBUS) if these are connected to an S7-1200 or S7-1500. The Reset function blocks

required for these communications modules can be found in the appendix.

Position in the information landscape

●

In addition to these operating instructions, you require the operating instructions

"SIMATIC S7-1200 programmable controller

(

http://support.automation.siemens.com/WW/view/en/36932465

)".

●

The manual of the particular RFID system contains information on the readers / write/read

devices to be connected.

●

Special information on the expert parameters and parameter assignment of the

RF620R/RF630R readers in conjunction with the RF120C communications module can

be found in the "Configuration manual RF620R/RF630R

(

http://support.automation.siemens.com/WW/view/en/33287195

)".

Recycling and disposal

●

The components of the RF120C communications module have low pollutant levels which

means that it can be recycled.

●

Contact a certified electronic-waste disposal company to recycle and dispose of your old

equipment in an environment-friendly manner.

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды