Siemens SIMATIC RF120C Скачать руководство пользователя страница 19

Страница: 19 / 92

Mounting, connecting up and commissioning

3.4 External power supply

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

3.4

External power supply

Power supply

The 3-pin socket for the external 24 VDC power supply is located on the top of the module.

The reader is supplied with voltage via this power supply. The matching plug with screw

terminals ships with the product. If there is overload, the RF120C turns off the power supply

to the reader and signals this to the CPU.

①

Mounted terminal block for the 24 VDC power supply of the reader

Figure 3-4

Terminal block for the 24 VDC power supply

The RF120C is supplied with power via the backplane bus and can also be addressed and

commissioned without an external power supply from the SIMATIC S7-1200.

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды