Siemens SIMATIC RF120C Скачать руководство пользователя страница 67

Страница: 67 / 92

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

Appendix

A.1

Approvals and standards

A.1.1

Approvals

Note
Granted approvals on the type plate of the device
The specified approvals apply only when the corresponding mark is printed on the product.

You can check which of the following approvals have been granted for your product by the

markings on the type plate.

Current approvals

SIMATIC NET products are regularly submitted to the authorities and approval centers for

approvals relating to certain markets and applications.
Contact your Siemens representative if you would like a list of the current approvals or check

the Internet pages of Siemens Automation Customer Support:
Current approvals (

http://support.automation.siemens.com/WW/view/en/44632196

)

Go to the relevant product there and select the "Certificates" entry type from the "Entry list"

tab.

Approvals for SIMATIC NET products

You will find an overview of the approvals granted for SIMATIC NET products including

approvals for shipbuilding on the Internet pages of the Siemens Automation Customer

Support:
Overview of the approvals granted

(

http://support.automation.siemens.com/WW/view/en/57337426

)

Overview of the approvals and standards

The CM RF120C has the following approvals and meets the following standards:

●

cULus LISTED IND. CONT. EQ.

●

C-TICK

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды