Siemens SIMATIC RF120C Скачать руководство пользователя страница 24

Страница: 24 / 92

Parameter assignment and configuration

4.3 Parameter assignment with the device configuration

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

The following parameters exist with all Ident systems (RFID and code reading systems):

Table 4- 1

Standard parameters for all Ident systems

Parameter

Parameter value

Default value

Description

Baudrate Reader

19.2 kBd
57.6 kBd
115.2 kBd

115.2 kBd

After changing the baud rate, the reader must

be turned off and on again.

Presence Check

On
Off (RF field off)
Off (RF field on)

On = presence is reported as soon as there is

a transponder in the antenna field of the

reader
Off (RF field on ) = the presence check in the

FB is suppressed. The antenna on the reader

is nevertheless turned on as long as it has not

been turned off by a command.
Off (RF field off) = the antenna is turned on

only when a command is sent and it then turns

itself off again (RF300 only)

Reset ERR-LED

On
Off

Off

On = the flashing of the error LED on the

RF120C is reset by each FB reset.
Off = the error LED always indicates the last

error. The display can only be reset by turning

off the RF120C.

The following parameters are system specific according to the selection you made in the

"Reader" menu.

4.3.2.1

RF200

Table 4- 2

RF200 general

Parameter

Parameter value

Default value

Description

No further settings are necessary.

Table 4- 3

RF290R

Parameter

Parameter value

Default value

Description

RF power

0.50 - 5.00 W

1.00 W

Setting for the output power of the reader.

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды