Siemens SIMATIC RF120C Скачать руководство пользователя страница 48

Страница: 48 / 92

Service and maintenance

5.1 LED status display on the RF120C

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

Table 5- 1

LEDs below the upper cover of the housing

LED / colors Name

Meaning

green

DC 24 V

Indicates that voltage is being applied via the external 24 V

power supply.

green

PRE

Indicates the presence of a transponder.

yellow

Indicates live communication with the reader.

flashing red

ERROR

A flashing pattern indicates the last error to occur. The

meaning of the flashing patterns is explained in the section

"Error messages (Page 52)".

Note
LED colors when the module starts up
When the module starts up, all its LEDs are lit for a short time. Multicolored LEDs display a

color mixture. At this point in time, the color of the LEDs is not clear.

Display of the operating and communication status

The LEDs indicate the operating and communications status of the module according to the

following scheme:

Table 5- 2

Display of the basic states of the module by the "DIAG" LED

DIAG

(red / green)

Meaning

Comment

Off

Power OFF

green

Module configured

Configuration was completed successfully and

no error occurred.

flashing green

•

Startup

•

Module not configured

•

Firmware update

flashing red

•

Defect

•

Error

•

Alarm message

Check the ERROR LED and the 24 VDC LED

for more detailed error diagnostics.

red

Module defective

Replace the module.

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды