Siemens SIMATIC RF120C Скачать руководство пользователя страница 30

Страница: 30 / 92

Parameter assignment and configuration

4.4 Ident instructions

Communications module RF120C with application blocks for S7-1200 and S7-1500

Operating Instructions, 07/2013, C79000-G8976-C328-01

4.4

Ident instructions

To be able to operate the RF120C with various Ident systems, the TIA Portal provides you

with a global library. This library contains various Ident instructions.
The following table lists all the Ident instructions and program elements of the library.

Table 4- 14 Overview of the Ident instructions

Position

Type

Symbolic name

Description

Ident

instructions

(global library)

Ident application

blocks

Function block

Reset_Reader

These Ident instructions are available

so that the communication with the

Ident systems can be programmed as

simply as possible.

Read
Write
Read_EPC-ID
Write_EPC-ID
Set_Ant

PLC data type

HW_CONNECT_VAR

Separate data type for all Ident

application blocks for physical

addressing of communications

modules and readers and for

synchronizing the function blocks used

for each reader.

Function block

AdvancedCmd

Advanced command set. With the

Ident application block

"AdvancedCmd" it is possible to

access other commands from the Ident

command set.

Ident profile

Function block

Ident profile

One instruction, full flexibility. This

block is available for experts to be able

to include complex command

structures in their own program

sequence.

PLC data type

PIB_COMMAND

Data type for the Ident profile for

setting the command parameters.

PLC tags

PIB constants

Constants of the Ident profile

Содержание SIMATIC RF120C





























































































Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды

Siemens SIMATIC RF120C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF120C

Отзывы:

Похожие инструкции для SIMATIC RF120C

Бренды по названию

Популярные бренды